Author: Tata | Chief Wig Designer, WigIsFashion
Last updated: July 2026
So, you've got yourself a professional lace beard. Now comes the real challenge: making it look like it actually grew out of your face, not like a furry sticker.
I'm Tata, Chief Wig Designer at WigIsFashion. In this guide (and the step-by-step video below), I'm going to demystify the entire process — from that nerve-wracking first lace snip to seamlessly blending the edges into your skin.
For this tutorial, we're using our premium Clair Obscur: Expedition 33 Verso Handmade HD Lace Beard & Moustache Set MB010, applied on our colleague so you can see exactly how the lace behaves on actual skin.
🛠️ The Battle Gear: What You'll Need
Before you even think about putting glue on your face, gather your tools. No improvising here:
-
Your WIF Lace Beard & Moustache Set
-
Small, ultra-sharp scissors (curved nail scissors or sewing snips work best)
-
Professional wig glue / Spirit Gum
-
A stiff applicator brush
-
A steady mirror (preferably with good lighting)
-
Cotton pads & rubbing alcohol (for prep and clean-up)
🎬 The Breakdown: Step-by-Step Application
Check out the full video below to see these techniques in motion!
| Step | What to Do | Tata's Insider Secret |
| 01 | Rough-cut the excess lace | Don't go straight to the hairline yet. Cut a generous boundary around the piece first to make it manageable. |
| 02 | Trim the chin bulk | Lift the chin hairs upward and lightly snip the undersides to customize the density to your jawline. |
| 03 | Relieve the tension | Make small vertical snips along the curved edges of the lace so it hugs the contours of your face without bunching. |
| 04 | Clean up stray fibers | Gently trim away any wild, rogue hairs that are sticking out at awkward angles. |
| 05 | The final lace haircut | Cut the lace down to about 1-2mm from the actual hair ventilation line. Go slow. |
| 06 | Do a dry run | Hold the beard up to your dry face in the mirror. Memorize exactly where that top line sits. |
| 07 | Map your face | Use your finger (or a light eyeliner pencil) to mark a couple of reference points on your cheeks. |
| 08 | Prep the glue | Apply your adhesive and wait. Let it sit until it gets tacky—never apply lace to wet, runny glue. |
| 09 | Map the adhesive | Dot the glue starting from your chin center, then paint it outward following your guide lines. |
| 10 | The first contact | Anchor the center of the chin first, then gently press and roll the sides upward onto your cheeks. |
| 11 | Lock down the perimeter | Take a tiny bit of glue on your brush and lightly dab it right over the top edge of the lace to seal it down. |
| 12 | The melt down | Use a damp cotton pad (or a clean, flat tool) to firmly press the lace into your skin until the shine disappears. |
| 13 | Detail work | Snip away any stray hairs that got caught in the glue during application. |
| 14 | The final style | Gently run a wide-tooth comb or beard brush through to fluff and blend the fibers. |
💡 Pro Tips From US (Don't Skip These!)
⚠️ The #1 Mistake: Rushing the Glue If your beard starts lifting or sliding halfway through an event, 90% of the time it's because you pressed the lace down too early. Wet glue has no grip. It needs to be sticky and tacky to the touch. Wait those extra 60 seconds—it saves you a massive headache later.
✂️ Cut Conservatively You can always cut more lace off, but you can't glue it back on once it's gone. Work in tiny, millimeter-sized snips.
☀️ Chase the Natural Light Bathroom lighting is notorious for lying to you. If you're wearing this to a con or a theater stage, check your edges in natural light. It's the ultimate test to see if your lace edge is truly invisible.
Watch the Full Video
We filmed the entire process – no jump cuts, just a real person applying a real MB010 beard.
Shop More
Looking for your first (or next) fake beard?